Fresh 526 BAE fathead/Total Flow long block for sale

Motor parts left

Parts of this motor sold, Here is what is left

1 MSD pro mag 44 coil just checked by BR motorsports and not run since. $250

1 Complete set of head studs for older BAE long stud blocks. These are the large studs on the top row and smaller studs on the bottom. These may fit KB stg 10's or later as well. These have the hex head broached in them for easy install $300

17 Spare 4.375" Sleeves for +.100 tall BAE Billet blocks (May fit others) I think they are all new, will dbl check for buyer. $50 per sleeve or all for $700

System 1 billet wet sump pumps w/ fittings. Has had some stuff go through but was ran in an A/fueler since with no troubles. $300.

New -20 XRP oil line for Moroso billet wet sump pump to Moroso Dragster pan, XRP lightweight braided and factory crimped at XRP $100 (Paid over $158)

Matched 526 cid rotating assy
Bryant billet 4.375" crank w/ no cracks. std mains /.010 on 3 of the rod journals, std on the 4th journals
Set of New rod bearings matched to crank
8 New +.220 Brooks B2-L rods (Lightening rods sells them now)
8 New JE pistons+New Trend pins+ New pin buttons+New C&A/A&C rings between 12 and 12.5:1 cpr
3 spare new JE pistons
+any spare wrist pins, buttons, and rings that I have fit that setup.
$2,250

Billet tool steel bullet 60mm cam, Hanna Specs, works well w/ screw or roots, It does have a few dings on the outside edges of the journals. This does not effect operation and it was given a clean bill of health by Cantrel. $300

Several sets of Crane .904 2" spread lifters just back from being inspected by Chase at Crane Cams. I have 1 or 2 sets of the raised floor lifters popular with the Veney head users and the rest are all std $200 per set, spare pairs $25 ea.

Casale gear drive, Low runs. 14 hole vernier cam gear w/ hub for top fuel hex built in. Very nice $350

KB Gear cam gear for gear drive #64207 $50

BAE billet fuel pump extension needs bushing or welding in the end as the bearing is loose, Comes w/ new bearing. $100

2 New sets of Flatout head gaskets, 1 gasket has been torqued on a BAE billet block for mockup. All fire rings are the same so they will go right on any BAE block. Other set is new in package $150

Total flow large valve billet fatheads (Like BAE 5 but slightly outflow them) Dual plugs w/ new block off plugs. Complete heads w/ all titanium valves, all studs, new lash caps, spare valves, keepers, and lash caps for $2,000 making them the most inexpensive set of fatheads on the net. Springs are at approx 400 lbs (These have had some repairs in the inner head stud areas and the fire ring areas. They are far from ugly but not the prettiest either. They will function perfectly. Just back from Samsel's and he gave them a clean bill of health.

BAE 5s large valve billet fatheads, Dual plugs w/ block off plugs. All Titanium Victory 1 valves and All studs. These can be had as is with one head needing welding under 1 to 4 seats, 4 new seats, and 2 push rod tubes. All 8 fire rings were removed for repairs (Repairs were never started) so you would need 8 new fire rings as well. I figure repairs would be between $500-$800. As is would be $1,000, repaired and ready would be $2,000. One of the heads has inserts in all of the spark plug holes, I suspect they damaged one and the machinist did them all, nice repairs. Both heads may have some inserts in the inner head stud holes. These heads will function fine.

BAE magnesium dual plug valve covers (Excellent shape) w/ 8 spark plug tubes, Billet tube retainers, 8 Block off plugs, and like new (Possibly new) burn down breathers w/ fittings. $900

Complete MSD pro mag 44 setup, no runs since upgraded to Black Magic at BR motorsports, makes 48 amps now. Coil and non rev limiting points boxed checked checked at BR, New cap, rotor, cap adapter, and plug wires w/ spare used cap, rotor, plug wires, and cap adapter.
Complete setup $3,900

also available is:
A used but good shape set of dragster upright zoomies w/ restraint brackets, pins, and new gaskets that fit these heads $350 (have had some small repairs but are not worn out, coating is off where repairs where made. I would have them re coated to make them pretty but they are not bad right now. $350

New DBL walled FC zoomies for BAE 4/5 fatheads 1 warmup since new $600

Reactor flex plate, another spare Reactor 130 tooth even 6 bolt pattern 8 bolt hemi flex plate (Both w/ ring gear) Bolts, and torque convertor hub adapter $200

*****************
If your needing a Funny car/altered/ or dragster chassis, PSi roots inlet shoes, or odds and ends.... please see my other adds on ITA

Buyer pays Shipping.

Thanks,

Serious inquiries only please, calling is best.
Trevor Sherwood
727-364-4368
Soldierboy0098@yahoo.com

 

bump

Things that go bump in the night.....running out of lines

Trevor Sherwood

 

I will vouch for Trev on this one....its a GOOD motor!

 

Tim

On this one, has my street credit went down?....lol

Wait till you see the new stuff Tim, its friggin awesome!

Happy holidays Tim,
Trev

 

Bump

Bump it up

 

bump

Bump it up please

 

Bump

Tax refunds are coming, all the cool kids are buying fathead hemi's.......bump it up, lol

 

Bump

Bump it up please

 

bump

Last sale fell through, bump it up please

 

bump

bump it up

 

Bump

to the top please

 

Bump

Bump to the top please

 

Bump

Bump it up please

 

Bump

Bump it up please

 

Bump

Bump it up please

 

Price reduced

Pride reduced, Great deal with tons of spares

 

Bump

Bump it up please

 

Added Spare heads and a spare oil pump

Added spare heads and a spare oil pump

 

Some parts sold

Some parts sold, Bump to the top please

 

bump

bump it up please