Search Results

Search Again
Page 4 of 10
  1. Mike Canter
    Post

    10 inch RAM Pedal clutch

    How many stands and fingers on the clutch. Is it a 6 stand six finger, a nine stand nine finger or a 6 stand 9 finger?
    Post by: Mike Canter, Apr 28, 2008 in forum: PSI Superchargers Tech Questions
  2. Mike Canter
    Post

    OT: Internet access

    It ain't going to be as fast as the Hughes Net but it is cheaper. Because of the type format used the Sprint is faster than Verizon but not by...
    Post by: Mike Canter, Apr 27, 2008 in forum: PSI Superchargers Tech Questions
  3. Mike Canter
    Post

    Idle EGT`s

    The cylinder head temp (HCT) is actually measuring the physical temp of the chunk of aluminum and the EGT is measuring the temp of the exhaust at...
    Post by: Mike Canter, Apr 24, 2008 in forum: PSI Superchargers Tech Questions
  4. Mike Canter
    Post

    converting lbs per hour...

    Methanol weights 6.63 lbs per gallon. Multiply 14.5 GPM by 6.63 lbs which means you are flowing 96.135 lbs per minute. Times 60 minutes is 5768.1...
    Post by: Mike Canter, Apr 23, 2008 in forum: PSI Superchargers Tech Questions
  5. Mike Canter
    Post

    Idle EGT`s

    Danny, I believe that temp sensor goes under the spark plug in place of the gasket. Can't use that on a hemi. I need a sensor that will screw into...
    Post by: Mike Canter, Apr 23, 2008 in forum: PSI Superchargers Tech Questions
  6. Mike Canter
    Post

    Idle EGT`s

    Thanks guys.
    Post by: Mike Canter, Apr 23, 2008 in forum: PSI Superchargers Tech Questions
  7. Mike Canter
    Post

    Idle EGT`s

    Does anyone know who to get the temp sensors that screw into the heads so I can add one to my data logger.
    Post by: Mike Canter, Apr 22, 2008 in forum: PSI Superchargers Tech Questions
  8. Mike Canter
    Post

    Aluminum Rods How Many Runs

    Brian, good to hear from you. A question for you. Why the big difference in the amount of runs between a NHRA blown ProMod and a NHRA TAFC? We are...
    Post by: Mike Canter, Apr 15, 2008 in forum: PSI Superchargers Tech Questions
  9. Mike Canter
    Post

    MSD 44 amp mag

    Yep, they do eat up ignition wires and rotors.
    Post by: Mike Canter, Apr 15, 2008 in forum: PSI Superchargers Tech Questions
  10. Mike Canter
    Post

    Topolino nose cones

    Send an email and a copy of that picture to Randy Baker (aka) Rapid Randy at owencrist@mchsi.com. Randy is big in nostalgia race cars and can...
    Post by: Mike Canter, Apr 14, 2008 in forum: PSI Superchargers Tech Questions
  11. Mike Canter
    Post

    I need some help ASAP regarding engine balance.

    Since the pistons are not actually rotating mass on the crankshaft it should not make any difference.
    Post by: Mike Canter, Apr 12, 2008 in forum: PSI Superchargers Tech Questions
  12. Mike Canter
    Post

    Engine turns off at 8250

    I believe a MSD tester will only work if you have a 8973 ProMag controller
    Post by: Mike Canter, Apr 11, 2008 in forum: PSI Superchargers Tech Questions
  13. Mike Canter
    Post

    mike canter

    I occasionally go to HRE.
    Post by: Mike Canter, Apr 11, 2008 in forum: PSI Superchargers Tech Questions
  14. Mike Canter
    Post

    MSD 44 amp mag

    According to MSD the answer is NO. There is nothing in the mag generator or the associated boxes that needs perodic maintenace.
    Post by: Mike Canter, Apr 10, 2008 in forum: PSI Superchargers Tech Questions
  15. Mike Canter
    Post

    Engine turns off at 8250

    So what RPM chip was in it?
    Post by: Mike Canter, Apr 9, 2008 in forum: PSI Superchargers Tech Questions
  16. Mike Canter
    Post

    Engine turns off at 8250

    Does Leahy honor the MSD warrantee? If it is all new MSD stuff then I would recommend sending it to MSD so it is covered under warrantee. The MSD...
    Post by: Mike Canter, Apr 9, 2008 in forum: PSI Superchargers Tech Questions
  17. Mike Canter
    Post

    Specks of black on plugs, fat or lean?

    I have never had or seen black specs caused by nylatron.
    Post by: Mike Canter, Apr 5, 2008 in forum: PSI Superchargers Tech Questions
  18. Mike Canter
    Post

    Specks of black on plugs, fat or lean?

    I actually do not talk about black specks on the porcelein of a alcohol motor plug because it is not usually seen. Detonation that eats aluminum...
    Post by: Mike Canter, Apr 1, 2008 in forum: PSI Superchargers Tech Questions
  19. Mike Canter
    Post

    Blower boost formula ?

    So Spud when you say "Blower Output" you are saying cubic inches per one revolution of the blower?
    Post by: Mike Canter, Mar 29, 2008 in forum: PSI Superchargers Tech Questions
  20. Mike Canter
    Post

    Lencodrive advise needed

    Bob, was there much damage:eek:?
    Post by: Mike Canter, Mar 28, 2008 in forum: PSI Superchargers Tech Questions
Showing results 61 to 80 of 198 Next >
Search Again
Page 4 of 10