Search Results

Search Again
Page 5 of 6
  1. Sandracer695
    Post

    Breather Hose

    RBS stocks it.
    Post by: Sandracer695, Aug 7, 2013 in forum: PSI Superchargers Tech Questions
  2. Sandracer695
    Post

    LB20 Swap

    Mark, I have lapped the blower manifold on the motor its flat. O-ring sits up approx. .015. Rechecked injector to adaptor its silicone. Adaptor to...
    Post by: Sandracer695, Aug 7, 2013 in forum: PSI Superchargers Tech Questions
  3. Sandracer695
    Post

    LB20 Swap

    SoDak, I have a crank trigger on it. Timing is rock solid. We have tried taking timing out when on the trans brake to no avail. MSD 10 with power...
    Post by: Sandracer695, Aug 7, 2013 in forum: PSI Superchargers Tech Questions
  4. Sandracer695
    Post

    LB20 Swap

    I increased idle check to 8.5lbs. I leaned metering valve down to 40% leak. The engine just heated up quickly. So far the best results I have...
    Post by: Sandracer695, Aug 6, 2013 in forum: PSI Superchargers Tech Questions
  5. Sandracer695
    Post

    LB20 Swap

    Yes we have tried different idle check pressure. No change. It has a Lencodrive. Trans does not want to shift with idle any higher than 1700rpm....
    Post by: Sandracer695, Aug 6, 2013 in forum: PSI Superchargers Tech Questions
  6. Sandracer695
    Post

    How do you ID clutch finger ratios?

    Where the lever contacts the button on the pressure ring. That is the radius you are talking about. .093 is less aggressive than a .156
    Post by: Sandracer695, Aug 3, 2013 in forum: PSI Superchargers Tech Questions
  7. Sandracer695
    Post

    How do you ID clutch finger ratios?

    If its a centrifugal clutch it is the radius of the lever (finger).
    Post by: Sandracer695, Aug 3, 2013 in forum: PSI Superchargers Tech Questions
  8. Sandracer695
    Post

    Burst Disk Max Boost Allowed ??

    If I remember right back in the early 90s a guy came around the pits and showed us a test jig that he would put pressure to the panel till it blew...
    Post by: Sandracer695, Mar 20, 2013 in forum: PSI Superchargers Tech Questions
  9. Sandracer695
    Post

    Davenport Jetsize email?

    RBS carries the Jetsize program. www.rbssuperchargers.com. You can contact JR by e-mail.
    Post by: Sandracer695, Oct 29, 2012 in forum: PSI Superchargers Tech Questions
  10. Sandracer695
    Post

    coating magnezium

    Have it Dow 7 coated. Call Littlefield Blowers I think he sends parts out to be coated once or twice a week. Nice people too. Joe
    Post by: Sandracer695, Jul 30, 2012 in forum: PSI Superchargers Tech Questions
  11. Sandracer695
    Post

    Crank Shaft Rotations

    Approximately 650 revolutions from start line to finish line. Engine RPM is 8000 for about 3 seconds pulls down to about 6500 with clutch lockup...
    Post by: Sandracer695, Dec 16, 2011 in forum: Pit Buzz
  12. Sandracer695
    Post

    need a rear main seal asap can i get it at local auto parts

    Fel Pro part #BS 40240
    Post by: Sandracer695, Nov 13, 2011 in forum: PSI Superchargers Tech Questions
  13. Sandracer695
    Post

    Calibrating Crower Dial Indicator

    Crower or Molinari sell a setting fixture. Check your gauge often.
    Post by: Sandracer695, Oct 13, 2011 in forum: PSI Superchargers Tech Questions
  14. Sandracer695
    Post

    Wrench for tightening inside head bolts

    Matco 9/16 ratchet wrench fits the inner stud nuts. It fits TFX and BAE i don't if it fits other blocks. Hope the helps. Snap-On and Mac are to...
    Post by: Sandracer695, Sep 16, 2011 in forum: PSI Superchargers Tech Questions
  15. Sandracer695
    Post

    Hampton Super Charger Question

    Amos Satterlee uses Hampton blowers give him a call. 562-691-6773
    Post by: Sandracer695, Jun 21, 2011 in forum: PSI Superchargers Tech Questions
  16. Sandracer695
    Post

    New crane lifters

    cknight please check your PM Thanks Joe.
    Post by: Sandracer695, May 23, 2011 in forum: PSI Superchargers Tech Questions
  17. Sandracer695
    Post

    BAE 8 Head vs NRE Head

    How about repairing the NRE heads. If you break a valve off who can machine the chambers and ports back to what they were. Do you have to send...
    Post by: Sandracer695, Dec 7, 2010 in forum: PSI Superchargers Tech Questions
  18. Sandracer695
    Post

    jetting BBC PSI D 540

    Hi Tony, give me a call sometime I have a little info that may help you. Joe 559-287-0952
    Post by: Sandracer695, Jul 12, 2010 in forum: PSI Superchargers Tech Questions
  19. Sandracer695
    Post

    Used Blower Belts

    Yes they are GT but they are 84mm wide sorry. 14MGT-1568-84
    Post by: Sandracer695, Jul 12, 2010 in forum: PSI Superchargers Tech Questions
  20. Sandracer695
    Post

    Used Blower Belts

    How many do you want? I have about 20 1 and 2 run belts. $50.00 a piece. Joe
    Post by: Sandracer695, Jul 7, 2010 in forum: PSI Superchargers Tech Questions
Showing results 81 to 100 of 118 Next >
Search Again
Page 5 of 6