Recent Content by Creech

  1. Creech
    Post

    Mid 2000s 14-71 blower comparo

    Id say that before todays blower mods SSI was the best roots blower around. I worked on a dragster in the early 90's. In 94' 95' we had a early...
    Post by: Creech, Jun 10, 2015 in forum: PSI Superchargers Tech Questions
  2. Creech
    Post

    BBC Rod bearing clearance.

    What kind of rods? Id use + .001X extra clearance bearings and go for .003 either way and go for .003 .004 on the mains is perfect. Marty...
    Post by: Creech, Jun 8, 2015 in forum: PSI Superchargers Tech Questions
  3. Creech
    Post

    Get well soon Dave Germain - big trans explosion

    How about the bag completely cover the reverser (besides a hole for the outshaft and lever) before pulling the straps through, where you would...
    Post by: Creech, May 22, 2015 in forum: Pit Buzz
  4. Creech
    Post

    How to cool a bruno

    Here is what Elmo has to say on the matter.... https://www.youtube.com/watch?v=eC087mmgFEI
    Post by: Creech, Mar 5, 2015 in forum: PSI Superchargers Tech Questions
  5. Creech
    Post

    Push button switch needed

    http://www.wmco.com/Products/Air-Valves-and-Switches.aspx
    Post by: Creech, Feb 8, 2015 in forum: PSI Superchargers Tech Questions
  6. Creech
    Post

    Carb size

    http://treracingengines.com/trecarbs.shtml
    Post by: Creech, Feb 8, 2015 in forum: PSI Superchargers Tech Questions
  7. Creech
    Post

    industrial methanol and racing methanol

    It turns a green tint if theres much water in it. Marty
    Post by: Creech, Dec 11, 2014 in forum: PSI Superchargers Tech Questions
  8. Creech
    Post

    Hydraulic throw out bearing for lenco / crower setup

    I have a hydraulic clutch slave and master cylinder for a funny car in the 60's or 70's. not sure who made it . Its a sealed unit with about 1"...
    Post by: Creech, Dec 11, 2014 in forum: PSI Superchargers Tech Questions
  9. Creech
    Post

    from cast iron to aluminum

    Maybe the opposite? Like with an aluminum rod if you detonate it the rod bolt can crush the cap down onto the bearing. I have an aluminum 525...
    Post by: Creech, Dec 5, 2014 in forum: PSI Superchargers Tech Questions
  10. Creech
    Post

    Screw/ roots camshaft?

    There really isn't much difference they've been using R296/500-16 (336 duration 296@.050 .500 lobe lift 116 lobe separation) in alky funnycars...
    Post by: Creech, Dec 5, 2014 in forum: PSI Superchargers Tech Questions
  11. Creech
    Post

    Camshaft selection?

    Running a 471ci AJ 481X with a whipple at at lower RPM (around 9000 I guess ) these guys put a 286 in 278 ex @ .050 110 lobe separation in @ 106...
    Post by: Creech, Dec 3, 2014 in forum: PSI Superchargers Tech Questions
  12. Creech
    Post

    Screw/ roots camshaft?

    7 time IHRA champion Mark Thomas told me 15 yeas ago, that they had been using a 118 spread cam and were thinking about trying 119ls. Of coarse...
    Post by: Creech, Dec 3, 2014 in forum: PSI Superchargers Tech Questions
  13. Creech
    Post

    Adding timing back in at higher RPM

    I read something I think from WJ years ago, if a faster pitch is coming at you, you have to swing quicker. Marty rock and roll...
    Post by: Creech, Dec 3, 2014 in forum: PSI Superchargers Tech Questions
  14. Creech
    Post

    Which cylinders get the longer rods in a fathead hemi w/ roots blower on a 6" setback

    Two answer the question 1 & 3 have have around a .050 short rods even in some screw blown Hemi's with the opening in the rear. With chevys they...
    Post by: Creech, Nov 21, 2014 in forum: PSI Superchargers Tech Questions
  15. Creech
    Post

    piston to head clearance on a BBC

    with an aluminum block Ive run the pistons out .020 withe a .053 gasket. and the pistons just had a shadow of the head. Marty Creech
    Post by: Creech, Jul 8, 2014 in forum: PSI Superchargers Tech Questions