MBR - Arias 8.3 - BBC - Chrysler Parts, System 1 Oil Pump

Discussion in 'Noonan Classifieds' started by DANA WARDELL, Jun 20, 2015.

  1. DANA WARDELL

    DANA WARDELL Authorized Merchant

    Joined:
    Jul 14, 2010
    Messages:
    367
    Likes Received:
    7
    Arias/MBR 8.3 ltr parts and Misc Chrysler - BBC Chevrolet parts for sale:

    557 - 8.3 ltr engine, arias century aluminum water block hat to pan to pan, big and ugly, 14-71 littlefield, new pistons, new rods, new crank, front cover, 10 qt. oil pan, sol aluminum 8.3 ltr. water heads, rocker assemblies, mag, enderle pump, fuel lines manifold, valley cover, fresh build from B & B Performance $20,000 plus freight

    Billet 8.3 ltr cylinder heads with 2.40 valves, assembled with valves, springs and retainers $2000.00

    Billet 8.3 ltr later style MBR cylinder heads with 2.60 valves, assembled with valves, springs and retainers $3,500

    Billet dual plug 8.3 ltr cylinder heads $2,000

    Valesco 4.125 Crank for 8.3 ltr or Fontana blocks. Chrysler rod journals and rear 8 bolt flange. Oldsmobile mains, Chevrolet double keyway front snout. Standard and mag checked $1600

    Dan Olson 8.3 ltr, (2) 10 quart funny car/door car tapered, rear 4.5 inch by front 3.5 inch aluminum oil pan good condition $300.00

    Dan Olson 8.3 ltr, (1) 12 quart funny car/door car square rear 6.5 inch by front 6.0 inch oil pan good condition $300.00

    Arias/Fontana 8.3 ltr black powder coated magnesium dual plug valve covers $400.00

    Mallory Mag 4 - pair just freshened by Hunt in Sacramento to 4.5 volts $500 ea.

    RCD 1440 8mm GT carbon belt, NEW, $100.00 plus the ride

    Gates 1600 8mm GT rubber, like new $50.00 ea.

    Mark Williams coupler, part #39068-1-A / 10-574, 6" long, turbo 40 splines on one end 3rd member dragster coupler on other end 20 SPLINE COUNT, $80.00 plus the ride.

    Throttle cables, various lengths, approximated eight to chooses from, let me know length needed $20.00 ea, plus the ride.

    Large polished billet bottle clamp in nice condition $20.00 plus the ride.

    System 1, Chrysler " nitro " high volume oil pump with fittings and line $750.00 plus freight

    Magneto MSD/ Chrysler brass magneto gears 5 like new, 4 - single key way, 1 - splined, $25.00 each. Package deal on all $100.00 includes freight.

    RCD Chrysler front crank outer support plate good condition, 5.5 inch spacing on outer bolt holes $30.00 , includes freight.

    Chrysler - BAE/Chrysler front idler plates, stand, 4 to choose from 50.00 ea plus the ride.

    Call Dana Wardell (916) 849-3551 or e-mail phoenixmtrspts@aol.com.some pictures on Racing Junk #182511715. Additional pictures now available on above items posted, send me your e-mail.
     
    #1
    Last edited: Aug 22, 2020
  2. WD-50

    WD-50 New Member

    Joined:
    May 5, 2012
    Messages:
    49
    Likes Received:
    0
    BBC Parts

    RCD BBC front degree wheel with magnets, long snout for crank support application, like new $150.00.

    I'll take this , and are your 8mm pulleys GT or HTD

    Please PM me with your response And address to send funds .

    Thanks, Bill

    Please clear your PM box
     
    #2
    Last edited: Jun 20, 2015
  3. DANA WARDELL

    DANA WARDELL Authorized Merchant

    Joined:
    Jul 14, 2010
    Messages:
    367
    Likes Received:
    7
    Degree Ring

    I'll get back to you the next week on the pulleys, I have to figure out what combination we're going to run, engine is going into our car today and I have to figure out belt length and pulley combination and then I'll have some extras.

    Send the check for the degree ring and your address, I'll get it boxed up today and be ready to ship to you.

    Phoenix Motor Sports
    4291 Mac Lane
    Shingle Springs, Ca.95682

    Thanks Dana
     
    #3
  4. WD-50

    WD-50 New Member

    Joined:
    May 5, 2012
    Messages:
    49
    Likes Received:
    0
    Pulleys

    It seems you have been to busy to clean out your PM box Dana, Good Luck with the fresh Motor.

    Well , I guess if you are running , you will be able to tell me what pulleys are available.

    Please PM me back or text me whether they are : GT ? or HTD ? Tooth count ? Anodized ? Flat Back or Offset ?

    Thanks , Bill
     
    #4
  5. DANA WARDELL

    DANA WARDELL Authorized Merchant

    Joined:
    Jul 14, 2010
    Messages:
    367
    Likes Received:
    7
    All are GT, all are anodized with the exception of the 46 which is black i believe, no offset all standard flat back flanges. All are posted now. Sorry for the delay!
     
    #5
  6. WD-50

    WD-50 New Member

    Joined:
    May 5, 2012
    Messages:
    49
    Likes Received:
    0
    Pulleys

    Thank You , I will take the 54t pulley in accordance with the terms in your text

    Bill
     
    #6
  7. boostedgt500

    boostedgt500 Member

    Joined:
    Mar 30, 2015
    Messages:
    149
    Likes Received:
    2
    Dana, have you shipped the intake yet?
     
    #7
  8. dcurtis58

    dcurtis58 Member

    Joined:
    Nov 19, 2014
    Messages:
    32
    Likes Received:
    0
     
    #8
  9. dcurtis58

    dcurtis58 Member

    Joined:
    Nov 19, 2014
    Messages:
    32
    Likes Received:
    0
    #9

Share This Page