Recent Activity
Activity stream for all registered members at InsideTopAlcohol.
-
Jim Starkey replied to the thread Enderle Injection Tuning Help.
I did just as you said. And am still having this issue
May 31, 2024 at 7:39 PM -
Kenny Laughlin posted a new thread.
FOR SALE: Noonan 600 Billet Heads
Noonan 600 Billet Heads (New) Springs Titanium Retainers – Low Runs $6,250 CONTACT KENNY@ 817-219-7957 OR KENNY@DRPIND.COM
Forum: Noonan Classifieds
May 31, 2024 at 7:06 AM -
Kenny Laughlin posted a new thread.
FOR SALE: 526 BAE / Noonan Screw Blower Motor
526 BAE / Noonan Screw Blower Motor 128% Over BAE Block Noonan Billet intake Screw Blower Bryant Crankshaft (New) P&P Wet Sump Oil Pump...
Forum: Noonan Classifieds
May 31, 2024 at 7:03 AM -
Kenny Laughlin posted a new thread.
FOR SALE: 526 BAE Screw Blower Motor
526 BAE Screw Blower Motor 98%Over BAE Block Bryant Crankshaft – 5 runs Manton Rockers P&P Wet Sump Oil Pump Moroso Oil Pan w/ Oil Lines...
Forum: Noonan Classifieds
May 31, 2024 at 6:57 AM -
Kenny Laughlin posted a new thread.
FOR SALE: Noonan 526 Screw Blower Short-Block
Noonan 526 Screw Blower Short-Block 526 Noonan – 426R Billet Block 98% Motor Short-Deck 4,500 Bore 2” Lifter Spread 65mm CAM New...
Forum: Noonan Classifieds
May 31, 2024 at 6:54 AM -
Kenny Laughlin posted a new thread.
FOR SALE: Noonan 526 Screw Blower 98% over Motor
Noonan 526 Screw Blower 98% over Motor Noonan 426R Block Short-Deck 2” Lift Spread 65mm CAM New Sleeves/Finished hone (done by BAE) New...
Forum: Noonan Classifieds
May 31, 2024 at 6:46 AM -
quickcut replied to the thread Enderle Injection Tuning Help.
Seams your a long way out . You had the pump Flowed. Why did you buy a tune up as well then you will have a nozzles area with main size...
May 31, 2024 at 12:21 AM -
ATT liked WIDEOPEN231's post in the thread Lock-up system.
Lots have found the lockup too abusive to bottom end.Lockup at wrong time and motor will pull the rods out. Like any tool the wrong use...
May 28, 2024 at 5:26 PM -
Jim Starkey posted a new thread.
Enderle Injection Tuning Help
Looking for thoughts, help or suggestions please. I have a 505 BBC with 8-71 on Alcohol 13.1 static compression Enderle Bug Catcher...
Forum: PSI Superchargers Tech Questions
May 27, 2024 at 9:01 PM -
WIDEOPEN231 replied to the thread Lock-up system.
Lots have found the lockup too abusive to bottom end.Lockup at wrong time and motor will pull the rods out. Like any tool the wrong use...
May 27, 2024 at 5:02 PM -
WIDEOPEN231 replied to the thread Setting initial timing on MSD Mag 44.
Most pros run something like grid where you set timing thru computer and use crank trigger. the mag just has to be set to a base and...
May 27, 2024 at 4:58 PM -
WIDEOPEN231 posted a new thread.
Tool steel adjusters
Like most have had a issue of killing adjuster from time to time. Thinking about going nto all tool steel adjusters or at least on...
Forum: PSI Superchargers Tech Questions
May 27, 2024 at 4:54 PM -
WIDEOPEN231 replied to the thread TAD Exhaust Headers.
I have built quite a few sets. If I can get the plates which should not be problem I can have you a set built same week as get them.(...
May 27, 2024 at 4:49 PM