Race Parts for Sale

Discussion in 'Noonan Classifieds' started by Butch Blair, Aug 26, 2022.

  1. Butch Blair

    Butch Blair Member

    Joined:
    Feb 7, 2007
    Messages:
    759
    Likes Received:
    3
    CURRENT PARTS FOR SALE LIST


    Complete Donovan early hemi 430 cu in AJ heads


    10” AFT titanium 6 finger glide clutch, titanium stands, with trick steel lightened, scalloped flywheel, floaters and 3 disk for Hemi used in nostalgia t/f car $4000.00


    Kevlar sfi 7.1 engine containment diaper with frame straps $800,00


    Complete valve seat grinding set up with a lot of tooling including valve guide reamers, 5/16, 11/32, 3/8 pilots, stone holders, stone dressing stand, stones, air gun, valve spring tester, spring height gauge, spring shims, box and portable outside storage work tray, etc. $800.00 plus cost to ship


    Sunnen Hone rod and pin fitting machine 1.094 and 2.250 mandrills, brass rod pin inserts with Sunnen AG-Series Precision Gauge (note the gauge alone cost this) $1,500.00


    Portable parts washer with pump nice for race pit use $100.00


    Head revolving service stand $150.00


    Schifer/ Eaton mag center sections 11in ring gear, lots of quick change gears, axles ,etc, needs new pinion shafts $1000.00


    72’ dual element top fuel or fuel altered wing $2000.00


    Stripped out head stud repair kit 9 /16 or change ½” to 9/16 repair at the track $150.00


    Spark plug thread repair kit with new inserts $75.00


    Dial Bore gauge in wooden case, missing a clamp $75.00


    Direct drive unit with male rear coupler an 1 ½’ input shaft $200.00


    Goodyear 16” dual inner/outer tube $25.00



    Engle R-22 small core 45 degree 112 c/l fuel roller cam excellent $300.00


    Crower .904 roller lifters 7 pair $100.0


    New billet 6” pump extension with RCD pump drive for Rodeck early hemi $150.00


    Valves

    13 used 2.40 x 6.40 long x 11/32 stem 3.40 tip length titanium intake valves $30.00 ea (these are very nice long valves that could be cut to most any size)

    15 used 1.90 x 11/32 x 6.08 long .250 tip exhaust valves $30.00 ea

    Lots of stainless 1.940 x 3/8 x 5.04 x .250 tip length and 1 enconal valves $30.00 ea

    4 new 1.940”x 3/8” .250 tip length enconal exhaust valves 5.12 long $100.00 all

    20 used stainless exhaust valves 1.94 x 11/32 x 5.02 long 2.50 tip length @15.00 ea


    SSI 4 stand billet front blower covers $100


    Lots of various length ½” head studs 9 1/2 to 13 1/2 long $10.00 ea


    9 16 to 9/16 head studs $15 ea

    8 - 11”

    5 – 9 7/8”

    1 – 13”


    9/16 to ½ head studs

    5 – 117/8”

    1 – 9 3/16”

    1 – 9 3/8”


    Olson late model hemi zombie headers, double flanged 2 ¾” with egt bungs fits AJ or Brad stage 5 fuel heads $150.00


    C&A ring checker (for round) 4.280 $35.00


    Early Hemi 392 heads, ported intake an exhaust, o-ringed, bead blasted better than new condition (no valves) $800.00 ( may have Manley valves to fit)


    6 TFX 4.187 sleeves (std deck) good used $50.00 ea.


    GRP solid beam used rods 8 6.921 & 9 6.981 long with l-19 bolts 1.094 wrist pin size @ $50.00 ea


    Piston & rod holder made of wood with closing door to keep clean holds 10 assembled $75.00


    Tall & short heavy made wood rod & piston holders $ 25.00 ea..


    Copper hemi head gaskets .040 to .080 new 50.00 used $25.00 per set


    1 ½” and 1 3/8” drive shaft couplers, male, female, connectors, drive shafts etc. $50.00 ea.


    Snap On Digital / Pyrometer kit, check temp exhaust etc while engine is running $100.00


    Digital reading tire air checking / setting gauge (to the fraction) Bender Race Products $100.00


    Weight gauge unit that sits on the ground and extends inside a given wheel for measuring weight at any 4 points car (0 to 1000 lbs) $50.00


    AIRCO mini ac heli ark model 130 complete with hoses, torch, regulator, small argon bottle 19” x 5” x 9” high 110 volt. (A must have at the race track) $600.00


    Portable aluminum fixture with gauges and quick disconnect fittings, hoses, co2 bottle for checking and setting relief valves at the track (1 to 1,000 lbs) $300.00


    AFT air timer box for setting air timers $ 300.00


    Waterman fuel pump over drive units selection of racios $50ea


    MSD programmable ignition controller pn. 8975 (new) $400.00


    MSD 5 stage programmable delay timer $400.00


    MSD complete set up & parts for small cap 44 amp magneto $75.00


    Hemi oil pump to magneto drives old style or SAE $40.00 ea


    MSD large older style black 44amp coils $75.00 e


    MSD 8168 Pro Mag timing control box (new) $300.00


    MSD RPM activated switch kit new in package part # 8950 $50.00


    MSD new 44 amp mag small cap, rotor an top wire retainer $50.00


    Dave Benjamin single inlet fuel pumps with build in changeable gear sets to under drive or over drive (25 gpm to 55 gpm 1 3/8 or 2” inlet with quick disconnect attachment) $1200.00


    Enderle large billet nitro barrel valve fresh from Enderle with ck valves $500.00


    Billet aluminum fuel discharge block has 8 - 8 & 2 -12 AN outlet holes and 2 mounting holes (real nice) $100.00


    ¼” wheel spacers 5 on 5 $15.00 pair


    System one 1 ¼” fuel filter with new spare inter filter (real nice) $50.00


    Moroso single spin on filter bracket flat surface or frame mount $50.00


    Aluminum 10” Crower clutch donut plate for (peddle clutch) (very nice) $300.00


    Titanium six large stands and adjusters for 9/16” studs 2 disk $300.00


    9/16 flywheel studs 2 disk 3 disk and 4 disk lengths $ 100 per set


    Lenco Input shafts 1 3/8 spline 6 spline on end $50.00ea

    B&J input shafts 1 3/8 10 spline B&J fine spline on the ends $75.00ea

    Lenco input shafts 1 ½ 10 spline $75.00ea


    Lenco throw out bearing and collars (4 different lengths) $50.00ea


    Clutch disk 10 ½” 1 ½” 10 spline hubs excellent fresh surfaced $50 to $75 each, new $110 ea.

    10 ½ floaters 3 cutters $ 50 ea


    10” fresh cut large stand floaters $35 ea.

    10” fresh cut disk 1 3/8 10 spline $30 ea.

    10” 1 ¾” 10 spline disk used $30ea.


    Spark plugs

    Ecell 141 $1.50 ea.

    NGK BG 9 & 10 long reach plugs $1.50 ea.

    NGK R 9 & 10 recessed electrode $1.50 ea


    Mag idler pulley assembly 2 5/8” belt width $100.00


    Blower Pulleys aluminum hard anodized

    8mm GT $75.00 ea

    56t new $100.00

    61t

    62t

    8mm polished aluminum $75.00

    63t

    65t with degree cut into it $50.00


    14mmGT (.320 offset) (hard anodized) $75.00 ea

    29t new

    30t used

    31t used

    32t used


    !4mm GT flat back (no offset)

    35t used $65.00

    39t used $100.00

    40t used $100.00

    41t new $125.00


    13.9mm.

    27t $60.00 ea

    29t



    Added information and pictures available, all emails answered

    Near Needles California

    925 229 3572

    topfuel776@aol.com
     
    #1
  2. clodhopper

    clodhopper Member

    Joined:
    Oct 18, 2009
    Messages:
    33
    Likes Received:
    0
    #2
  3. GTPerf

    GTPerf Member

    Joined:
    Oct 22, 2006
    Messages:
    204
    Likes Received:
    5
    Can I get a picture? looking for a pump mount for a pump test bench im building Thanks gtperf@verizon.net
     
    #3
  4. WIDEOPEN231

    WIDEOPEN231 Member

    Joined:
    Jun 10, 2011
    Messages:
    126
    Likes Received:
    20
    #4
  5. WIDEOPEN231

    WIDEOPEN231 Member

    Joined:
    Jun 10, 2011
    Messages:
    126
    Likes Received:
    20
    how many ekg 9's do you have.
     
    #5
  6. Chev502

    Chev502 New Member

    Joined:
    Jul 17, 2014
    Messages:
    26
    Likes Received:
    0
    Hi do you still have the 4 x new 1.940” x 3/8” x 5.120” valves ?
    Cheers Murray
     
    #6
  7. Chev502

    Chev502 New Member

    Joined:
    Jul 17, 2014
    Messages:
    26
    Likes Received:
    0
     
    #7
  8. a/fd slngsht

    a/fd slngsht Member

    Joined:
    Dec 2, 2004
    Messages:
    315
    Likes Received:
    3
    If butch can not help you, I may.. I have some 1.950 3/8 stem 55 degree valves... Mike
     
    #8

Share This Page