MBR - Arias 8.3 Engines - BBC RCD Crank Hub and Front Crank Support

Discussion in 'Noonan Classifieds' started by DANA WARDELL, Jun 20, 2015.

  1. DANA WARDELL

    DANA WARDELL Authorized Merchant

    Joined:
    Jul 14, 2010
    Messages:
    335
    Likes Received:
    4
    557 - 8.3 ltr engine, arias century aluminum solid block hat to pan to pan, big and ugly, 14-71 littlefield, new pistons, new rods, new crank, front cover, 10 qt. Milodon oil pan, aluminum 8.3 ltr. water heads, rocker assemblies, mag valve covers, 110 enderle pump, barrel valve, fuel lines, manifold, valley cover, flex plate, starter, ready to install and run, fresh build from B & B Performance $18,000 plus freight Sold!

    Billet 8.3 ltr cylinder heads with 2.40 valves, assembled with titanium valves, springs and retainers $2400.00

    Billet 8.3 ltr later style MBR cylinder heads with 2.60 titanium valves, assembled with valves, PAC springs and retainers $3,300

    Valesco 4.125 Crank for 8.3 ltr Arias or Fontana blocks. Chrysler rod journals and rear 8 bolt flange. Oldsmobile 3" mains, Chevrolet double keyway front snout. Standard journals and fresh mag check $1200.00 plus freight. Sold !!!!!!!

    Dan Olson 8.3 ltr, 10 quart funny car/door car tapered, rear 4.5 inch deep, front 3.5 inch deep aluminum oil pan, no windage tray, decent condition $200.00 plus freight

    MSD12 Large cap magneto with points box and coil, Chevrolet cw rotation $1100.00. With Hemi wires additional $150.00

    Mallory Mag 4 - pair just freshened by Hunt in Sacramento to 4.5 volts, Hemi rotation $400 ea.

    RCD 1440 8mm GT carbon belt, NEW, $100.00 plus the ride

    Gates 1600 8mm GT rubber, like new $50.00 ea.

    Mark Williams coupler, part #39068-1-A / 10-574, 6" long, turbo 40 splines on one end 3rd member dragster coupler on other end 20 SPLINE COUNT, $80.00 plus the ride.

    Throttle cables, various lengths, approximated eight to chooses from, let me know length needed $20.00 ea, plus the ride.

    Large polished billet bottle clamp in nice condition $30.00 plus the ride.

    Dual mag drive with billet dual mag hand cuff and two stainless mag clamps $600.00

    RCD-BBC front long nose crank hub and front crank support with spacers $800.00 plus the ride.

    RCD front crank outer support plate good condition, 5.5 inch spacing on outer bolt holes $50.00, includes freight.


    Call Dana Wardell (916) 849-3551 or e-mail phoenixmtrspts@aol.com.some pictures on Racing Junk #182511715. Additional pictures now available on above items posted, send me your e-mail.
     
    #1
    Last edited: Nov 23, 2021 at 9:43 AM
  2. WD-50

    WD-50 New Member

    Joined:
    May 5, 2012
    Messages:
    49
    Likes Received:
    0
    BBC Parts

    RCD BBC front degree wheel with magnets, long snout for crank support application, like new $150.00.

    I'll take this , and are your 8mm pulleys GT or HTD

    Please PM me with your response And address to send funds .

    Thanks, Bill

    Please clear your PM box
     
    #2
    Last edited: Jun 20, 2015
  3. WD-50

    WD-50 New Member

    Joined:
    May 5, 2012
    Messages:
    49
    Likes Received:
    0
    Pulleys

    It seems you have been to busy to clean out your PM box Dana, Good Luck with the fresh Motor.

    Well , I guess if you are running , you will be able to tell me what pulleys are available.

    Please PM me back or text me whether they are : GT ? or HTD ? Tooth count ? Anodized ? Flat Back or Offset ?

    Thanks , Bill
     
    #3
  4. WD-50

    WD-50 New Member

    Joined:
    May 5, 2012
    Messages:
    49
    Likes Received:
    0
    Pulleys

    Thank You , I will take the 54t pulley in accordance with the terms in your text

    Bill
     
    #4
  5. boostedgt500

    boostedgt500 Member

    Joined:
    Mar 30, 2015
    Messages:
    149
    Likes Received:
    2
    Dana, have you shipped the intake yet?
     
    #5
  6. dcurtis58

    dcurtis58 Member

    Joined:
    Nov 19, 2014
    Messages:
    32
    Likes Received:
    0
     
    #6
  7. dcurtis58

    dcurtis58 Member

    Joined:
    Nov 19, 2014
    Messages:
    32
    Likes Received:
    0
    #7
  8. Ron Sapp

    Ron Sapp New Member

    Joined:
    Jan 30, 2020
    Messages:
    17
    Likes Received:
    0
    Hello Dana, I will take one of the tapered 10 qt oil pans for $300.00 if still available. Text or email me price with shipping.
     
    #8
  9. DANA WARDELL

    DANA WARDELL Authorized Merchant

    Joined:
    Jul 14, 2010
    Messages:
    335
    Likes Received:
    4
    Send me your zip code for the freight cost. DW
     
    #9
  10. WIZBANG

    WIZBANG Member

    Joined:
    Nov 8, 2004
    Messages:
    761
    Likes Received:
    1
    Sent you an email and text ?
     
    #10
  11. DANA WARDELL

    DANA WARDELL Authorized Merchant

    Joined:
    Jul 14, 2010
    Messages:
    335
    Likes Received:
    4
    Bumpty Bump
     
    #11

Share This Page