Is it possible for a blower to…

Discussion in 'PSI Superchargers Tech Questions' started by Bjs344, Oct 9, 2021.

  1. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    Take a 1000 hp to spin?

    kobelco 14-71 std helix with minor dmpe mods.

    At 20 over it should be moving 1500 hp worth of air and making 40 psi of boost.

    it makes the right boost number according to my data.

    If I put 1500 hp worth of fuel to it, it makes 750 hp and just barely colors the plugs (assume 2 lb/hr/hp and 4.1 target. Ya I know, that’s a lean target but at 3.5 it makes even less power)

    if i put 1200 hp worth of fuel to it, it makes 850 hp and burns all the plugs to the top thread.

    If I put 1000 hp worth of fuel to it it will make 1000 hp for about 1 second before it torches the heads completely off.

    The blower case never gets hot on a run, but I don’t measure iat yet.

    is it possible for a blower to be bad enough to soak up 600 hp more than a normal blower or almost 1000 hp total????

    I’ve changed converters twice and rear gears once but the power just isn’t there. Different heads, cam. 50% through the blower up to 80% through the blower. I can make the plugs look exactly how I want on every cylinder with no problem.

    Only oddity is the right side idles WAAY lean even if I flood it with the barrel valve. Actually only 2,4, and 6. 7 and 8 are so far at idle they’re hard to keep lit.
     
    #1
  2. jay70cuda

    jay70cuda Well-Known Member

    Joined:
    Sep 30, 2009
    Messages:
    1,139
    Likes Received:
    35
    I've ran Dmpe stuff a bunch and it was always good. Sounds like you got an electrical issue.
    Both heads grounded to the coil ?
    44 amp mag?
    Maybe we need some details on your setup to better help
     
    #2
  3. Mike Canter

    Mike Canter Top Dragster
    Staff Member

    Joined:
    Mar 10, 2004
    Messages:
    4,630
    Likes Received:
    189
    What engine is this blower sitting on? How many cubes? If you take the blower belt off and turn the blower by hand how hard is it to turn?
     
    #3
    Last edited: Oct 10, 2021
  4. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    326” LS.

    stock coil on plug. Same basic motor made about 1500 hp with a turbo on top.

    Ive verified timing all the way to 7000 rpm, but it could be off by a couple degrees. Sounds great all the way to 9000 rpm. I wouldn’t say it pulls, but it definitely doesn’t nose over or misfire at all. Super crisp and clean above 7000.

    I’ve had timing all the way from 18 to 28. Most guys with this combo underneath a turbo run 18-24 degrees total although I’ve heard of maybe one at 30 degrees. 65cc chamber that I softened just a little. Small dome. About 10.5:1 compression.

    I’ve flogged this thing to death and blown it up or torched the heads about 8 times both on the chassis dyno and on the track. It just won’t make any power unless it’s dead lean and even then it’s hundreds of horsepower shy.

    I was going to just start adding 2 degrees at a time yesterday until it blew up but it lifted a head while making dismal power at 28 degrees.

    I tried turning the blower down and only making 30 psi in case blower speed was getting too high, but the power was down about like you’d expect for giving up 10 psi of boost.

    I’ve had it stal anywhere from 6000 - 7800, shifted it anywhere from 7500-9000. All about the same.

    I think Ssi has a blower dyno so maybe I just need to get it up there? Or call Davenport, but not sure I have the blank check for his help.

    i didn’t actually get the blower from dmpe. Got it from an offshore guy who had the email from dmpe where it had been sent in a long time ago. The case has been machined on the bottom in front of the rotors so somebody worked on it.

    almost forgot, Mike, it spins super easy by hand. I figured since it’s making 40 psi like it should be at 20 over, why bother restripping? I have an Ssi high helix that’s even looser and it ran great on my bbc stuff. I was planning on putting the high helix on this deal just to see (wouldn’t be class legal) but I’d have to cut the dash bar out.
     
    #4
    Last edited: Oct 10, 2021
  5. WIDEOPEN231

    WIDEOPEN231 Member

    Joined:
    Jun 10, 2011
    Messages:
    112
    Likes Received:
    17
    IMO do not get over hung up on numbers. Boost is just a referance tool. Lots of things play into it. Valve size,cam design ,head flow and temp of air coming out the blower.
    I understand the x amount of fuel for x amount hp.Are you taking into account that the reason you put fuel thru top is to help cool the blower? It also gets less fuel out becuase when you are cooling it some is vaporized(for lack of better wording).
    Some times you have to listen to the motor and screw the math or to use word thats popular now days.Screw the science. If you want to run x amount fuel and its rich.Add blower thats why the pulleys have bolt holes. If rules limit blower over drive thats where you have to lean it some. Tune motor by what it is doing and what it wants not what some formula tells you what it should want. Just a old guys opinion.
     
    #5
    bandit496 likes this.
  6. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    Chris, if I was on your side of the fence, I would agree with you 100%. But if I extrapolate from where I’m at now, I would need about 6000 lb/hr and of fuel and about 90 psi boost to make 1500 hp. Same motor made close to 1500 with a turbo around 40 psi.

    In hindsight, I should have left the fuel up closer to 3000 lb/hr when I started turning the timing up, but the plug was so cold I though I could take away a little fuel too.

    So, has anybody ever seen a blower rob hundreds of hp more than normal?? Whether due to assembly error or anything else? I’ve knocked it off the intake twice, but it always spun ok afterwards. Any way I damaged it without any visual signs or binding?
     
    #6
  7. jay70cuda

    jay70cuda Well-Known Member

    Joined:
    Sep 30, 2009
    Messages:
    1,139
    Likes Received:
    35
    Knocking the intake off is extreme lean conditions. A barrel valve isnt perfect but it dumps a lot of fuel during the transition from trans brake to wot. Not many people have made efi work on blower. Maybe talk to Jon at resolution racing. He ran it for a while and I'm sure he could crunch fuel numbers with you.
     
    #7
  8. Mike Kern

    Mike Kern Member

    Joined:
    Aug 17, 2010
    Messages:
    51
    Likes Received:
    10
    First thing I'd look for is if the rotors are in backwards. With the snout pointed at you (and looking at the inlet) the rotors should make a V shape (V for Victory), If it looks like and A, you're an A($$hole).
     
    #8
    WIZBANG and ta455 like this.
  9. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    No efi here. All my numbers are based on spuds calculator plus the pump flow sheet.

    I knocked the blower off because the ports weren’t opening fast enough. I understand why it happened now. I can explain but don’t want to start an argument about that in this thread. Didn’t have data the first time but the second time I had a pressure transducer in the port distro and it was very obvious what happened.

    no victories here but I do have a v in the rotors. Actually woke up in the middle of the night a few weeks ago and went out to the garage to verify.
     
    #9
    Mike Kern likes this.
  10. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    Something else I just thought of.

    last week i stall checked it in the driveway before putting it on the trailer. 7900 on the button and climbing. Motor wasn’t ice cold but it wasn’t warm.

    changed nothing, took it to the track, warmed it up. Did a decent burnout. Air is maybe a tiny bit worse. It goes 7000 on the button.

    the blower case doesn’t get warm but is it possible something happens to it as it warms up to completely mess up the airflow??

    something else I hadn’t thought of: when the motor is relatively cold I can flick it to the moon in neutral. By the end of the day it just wants to labor until I give it a bunch of throttle. Didn’t even realize it till just now, but i think it’s been that way for a long time, maybe ever since I put it together.
     
    #10
  11. kosky racing

    kosky racing Comp Eliminator

    Joined:
    May 11, 2003
    Messages:
    890
    Likes Received:
    48
    something stupid ----but could there be tape or a covering on the manifold opening -seen clear tape covering blower discharge and openings- also on manifolds!
     
    #11
  12. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    Lol, that would be a good one. I’ve had the blower off no less than 20 times since I started this deal a year ago so I don’t think I missed anything being taped up. But it just about has to be something almost that stupid.
     
    #12
  13. MaineAlkyFan

    MaineAlkyFan Active Member

    Joined:
    Oct 8, 2006
    Messages:
    364
    Likes Received:
    53
    Two thoughts... Heat seems to be a factor, maybe when the case or rotors heat up something is binding? The blower dyno would show up some kind of heat induced mechanical loading.

    What else changed when you went from turbo to blower? Plumbing. Wires. Ignition. We chased a lean cylinder for a while that was perfect except during the run. Ended up being a nozzle line with a pinhole in the inner jacket of the hose. Tested & looked fine, but during the pass, fuel pressure would balloon up the inner liner & restrict flow. Maybe something like that on another system that happened to change at the same time as the blower swap.

    Chris Saulnier - Team Tigges
    Mechanic Falls ,Maine
     
    #13
  14. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    Ya, I definitely need to get the blower looked at and on the dyno.

    the turbo setup wasn’t mine, I just bought the motor and bolted on a blower intake. But there’s dozens of combos just like that turbo setup out there. Any hillbilly with a laptop can make 1500 on these things with a turbo on it. All the turbo guys say it’ll never run with a blower on it. Unfortunately I think this is currently the fastest 14-71 Ls in the world, but that’s just because it’s the only one that’s been down the track.
     
    #14
  15. Fat60

    Fat60 New Member

    Joined:
    Nov 15, 2013
    Messages:
    1
    Likes Received:
    1
    So what happened? Did you fix ?
     
    #15
    WIZBANG likes this.
  16. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    Had the blower inspected and restripped. Didn’t appear to be anything wrong. Went from

    boost: 28.9
    Flow: 4011

    to

    boost: 31.6
    Flow: 4171

    all at 11,750 rpm which is just slightly faster than I ever spun it. Boost and flow were pretty linear all the way up the rpm sheet. They said a real good fuel blower would beat that by 20% but it should be enough for what I’m doing right now.

    I took the whole deal to some guys that know more than me. They are trying to get it on the engine dyno in a couple weeks. I’ll let you know.
     
    #16
    WIZBANG likes this.
  17. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    Turns out the guys I took it to are way smarter than me because they decided they didn’t want to work on this heap at all.


    Got it back together anyway and took it out once.
    I fixed the valve float from last year which is letting it burn way more fuel (like .040 smaller main to run the same ET) except now it is blowing out the spark. 1500 hp worth of air, probably 13-1400 hp worth of fuel and the plugs showed just a little heat on what I think is real low timing. Hard to say how much power it’s making because it’s really peaky with a tight converter and a glide so the ET shows like 1000 hp or something like that.

    I put my tight converter in with super high hopes that I could stretch it out. Didn’t work. Flashed about 7000. Complete dog until 8200.

    Going to change to real coils (ign1a) and put the loose converter in (hopefully 8400).

    was planning to stiffen the valvetrain up a little more just to be safe but not sure I can get the parts.
     
    #17
  18. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    Little bit of an update for anybody interested:

    Turns out there was no valve float or spark blowout (nothing significant anyway). It runs the same with ign1a a and solid roller lifters.

    The whole combo was just really pissed off. The blower did not like being on this teeny tiny motor.

    After changing everything twice, I got out the rig welder and the grinder and made some “airflow mods” and the car picked up .2 and 5 mph to the 1/8 mile and ALL the heat was gone from the plug.

    best I can tell the blower was only moving 1000 hp worth of air and is probably closer to 1250 hp worth now which is way less than it moved on the SSI blower dyno.

    If you all know anybody that is willing to modify an old cast case (required by class rules) let me know
     
    #18
  19. TOL

    TOL Active Member

    Joined:
    May 18, 2005
    Messages:
    1,350
    Likes Received:
    17
    What is driving your IGN1A coils ?
     
    #19
  20. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    TOL, I’m using a Haltech VMS ignition controller and some kind of fancy “big wire” harness. I’ve verified timing up to 7k (which is pretty damn scary on a blower motor).
     
    #20

Share This Page