Spark Plug Gap

Discussion in 'PSI Superchargers Tech Questions' started by aort, Jun 6, 2017.

  1. aort

    aort Member

    Joined:
    Sep 26, 2010
    Messages:
    55
    Likes Received:
    0
    I'm running a 557 MBR with a 1471 M5 on alcohol. I'm having an issue with the plug gap in one cylinder. I am using 6061-10 plugs and gap them at .014". The first test run of the season, #4 cylinder went dead around half way through the pass and when I check the plug it was .018" plus. The rest were at .014". I thought I either missed one or it was a bad plug. Put a new set in for the weekend and on Friday it ran fine. I didn't think to check the gap since it ran good. I put the same plugs back in for the second run and about half way through, #4 went dead again. Checked the plug gaps and sure enough, #4 is .018" plus and the rest are still a snug .014". Just eyeballing the center of the plug, it doesn't seem to be sinking. What could be the cause?
     
    #1
  2. Mike Canter

    Mike Canter Top Dragster
    Staff Member

    Joined:
    Mar 10, 2004
    Messages:
    4,630
    Likes Received:
    189
    Interesting. First let me say a many years ago we ran all plugs at .018" then we found out that if we gapped them at .015" they fired better during the launch when the mixture was super rich. So that cylinder should not go dead with a .018" gap. Since it is doing on several plugs then there must be some force within that cylinder. That can only be detonation or preignition. Try a different plug wire and check the inside of the cap for spark tracking and cracks. What is the most retard you put into the motor during the run?
     
    #2
  3. aj481x

    aj481x Member

    Joined:
    Jan 27, 2004
    Messages:
    976
    Likes Received:
    18
    Mike is right, .018" won't hurt it. Put on a brand new plug wire and check rotor phasing.
     
    #3
  4. aort

    aort Member

    Joined:
    Sep 26, 2010
    Messages:
    55
    Likes Received:
    0
    All of the plug wires have 5 runs on them. I'll check under the cap. I used to gap them at .015", but tried to tighten it up a little to see if it solved anything. It is in a pulling truck, so my timing is the same all the way through the run. You can see the cylinder miss intermittently from about 6000-7000 rpm and then above 7000 its just blowing raw fuel. The rest of the ignition is clean, just that one cylinder when the pressure starts to build.
     
    #4
  5. kosky racing

    kosky racing Comp Eliminator

    Joined:
    May 11, 2003
    Messages:
    888
    Likes Received:
    48
    Change the plug wire!
     
    #5
  6. Mike Canter

    Mike Canter Top Dragster
    Staff Member

    Joined:
    Mar 10, 2004
    Messages:
    4,630
    Likes Received:
    189
    You can have a new plug wire that has a defective connection on one of the ends
     
    #6
  7. Blown5402

    Blown5402 Member

    Joined:
    Aug 12, 2011
    Messages:
    577
    Likes Received:
    8
    Same as Mike says, I have had 2 sets of new wires and one would not fire all the way through a run. Changed it and all was OK!
     
    #7
  8. aort

    aort Member

    Joined:
    Sep 26, 2010
    Messages:
    55
    Likes Received:
    0
    Not saying it isn't the wire, I can change it.

    How does the gap increase?
     
    #8
  9. jay70cuda

    jay70cuda Well-Known Member

    Joined:
    Sep 30, 2009
    Messages:
    1,139
    Likes Received:
    35
    Wires do weird things. I use Moroso now after talking with Jonathan young tuner on here. He is a dealer for lot of parts and is a straight shooter. Give him a call. He's seen a lot of things.
     
    #9
  10. jeffj

    jeffj Member

    Joined:
    Mar 8, 2008
    Messages:
    225
    Likes Received:
    12
    If the cylinder is detonating it can start to push up the crimp on the plug which holds the porcelain in place. If it pushes up, the center electrode goes up with it, away from the ground strap which increases the plug gap. Way back in the day, I have seen porcelains shot right out of the plug case after a few runs on the same plugs with some detonation. That would explain the increased gap but why would it stop firing? If it stopped firing and then hydrauliced it could jack up the porcelain and produce the same effect. So you are back to why does it stop firing....fat cylinder and it washes out? Does the plug show hot or cold?
    Jeff Johnsen
     
    #10
  11. aj481x

    aj481x Member

    Joined:
    Jan 27, 2004
    Messages:
    976
    Likes Received:
    18
    Inspect the boot inside and out for black tracks.
     
    #11
  12. aort

    aort Member

    Joined:
    Sep 26, 2010
    Messages:
    55
    Likes Received:
    0
    The first time they were new plugs, #4 showed a half burn while the rest were full, not quite up any threads. When it ran good over the weekend on new plugs, they all showed the same, maybe starting to creep up that first thread. Since I used the plugs again, I can't tell the heat the second time.
     
    #12
  13. Mike Canter

    Mike Canter Top Dragster
    Staff Member

    Joined:
    Mar 10, 2004
    Messages:
    4,630
    Likes Received:
    189
    #13
  14. aort

    aort Member

    Joined:
    Sep 26, 2010
    Messages:
    55
    Likes Received:
    0
    Mike I have read your article and pulled this from it

    That is pretty much where it is. They aren't quite burning up the threads yet. I ran it with this tune up all of last year. Since they run 12-15 seconds, I have 18 gpm going to it. I'll take a closer look and see if I can see the porcelain moving at all.
     
    #14
  15. Mike Canter

    Mike Canter Top Dragster
    Staff Member

    Joined:
    Mar 10, 2004
    Messages:
    4,630
    Likes Received:
    189
    Ok, just wanted to make sure so you don't damage your motor
     
    #15
  16. Bjs344

    Bjs344 Member

    Joined:
    Sep 10, 2013
    Messages:
    355
    Likes Received:
    24
    I realize it's off topic, but mine doesn't get real sporty until at least the 2nd thread.
     
    #16
  17. Mike Canter

    Mike Canter Top Dragster
    Staff Member

    Joined:
    Mar 10, 2004
    Messages:
    4,630
    Likes Received:
    189
    Heat in the plugs is a combination of timing and fuel. Having the motor not perform until the heat gets down to the second thread maybe an indication that one or the other or both is not correct.
     
    #17

Share This Page